Enter here the maximum ratio of the corner length to the outline/inline distance. For example if the distance is 2 and the ratio is 10, corners longer than 20 will be cut. A good value is 10. The minimum value is 1.
Rounded Joins
Click here to round corners of the outline/inline paths. See example on left.
Mitered Joins
Click here to miter corners of the outline/inline paths. Enter on the right the maximum length of the corner.
Rounded Caps
Click here to round ends of the outline/inline paths. See example on left.
Inline
Enter here the inline’s distance from the selected paths.
Outline
Enter here the outline’s distance from the selected paths.
Inline
Switch on to create an inline of the selected paths. Enter on the right the inline’s distance from the paths.
Original
Switch on to keep the original paths.
Outline
Switch on to create an outline of the selected paths. Enter on the right the outline’s distance from the paths.
Tight Freehand Tolerance
Switches on or off the feature which smooths the curves of your freehand drawing.
Available Memory
Switches on or off the indicator that shows the amount of available memory.
Angle and Distance
Switches on or off the indicator that shows your distance and angle from the place that you started dragging from.
Relative Position
Switches on or off the indicator that shows your position relative to the place from where you started dragging.
Current Position
Switches on or off the indicator that shows your current position in the document.
Border line
Draws division lines between different areas in the same section.
Snap to Point
Click here to switch on or off the Snap to Point function.
Display Curve Levers
Click here to show or hide the handles that connect anchor points with control points on the paths.
Direction Line
Draws lines that will determine the direction of the stitches.
Scale Origin
Click here to scale the selection from the point at which you clicked.
Scale Origin
Click here to scale the selection around its own center.
Shear Origin
Click here to shear the selection from the point at which you clicked.
Reflection Origin
Click here to reflect the selection from the point at which you clicked.
Worksheet Height
Enter here the worksheet height.
Worksheet Width
Enter here the worksheet width.
Grid Height
Enter here the grid height.
Grid Width
Enter here the grid width.
Radius
Enter here the radius of the polar grid.
Angle
Enter here the angle of the polar grid. The angle ranges from 0° to 180°.
Magnification
Enter here the magnification value for the view of the document. For example 50% will zoom out by a factor of 2.
This dialog allows you to change the functions of the pointer.
Template Heigth
Enter here the heigth of the template. Press Tab to apply.
Template Width
Enter here the width of the template. Press to Tab to apply.
Vertical Template Scale
Enter here the vertical scale of the template. For example 200% means you want to double its size. Press Tab to apply.
Horizontal Template Scale
Enter here the horizontal scale of the template. For example 200% means you want to double its size. Press Tab to apply.
Angle of Movement
Enter here the angle of the direction line. Press Tab to apply.
Distance of Movement
Enter here distance that you wish to move the selection. Press Tab to apply.
Vertical Movement
Enter here the vertical movement value of the selection. Positive values move it up and conversely. Press Tab to apply.
Horizontal Movement
Enter here the horizontal movement value of the selection. Positive values move it to the right and conversely. Press Tab to apply.
Shear Origin
Click here to shear the selection around its own center.
Reflection Origin
Click here to reflect the selection around its own center.
Reflection Angle
Enter here the angle of the axis around which you wish to reflect the selection. For example 0° reflects it around the horizontal axis. The angle ranges from -180° to +180°.
Transformation Origin
Click here to transform the selection from the point at which you clicked.
Height
Enter here the height of the selection. Press Tab to apply and new scales will be calculated.
Width
Enter here the width of the selection. Press Tab to apply and new scales will be calculated.
Uniform Scales
Click this box to have proportional scaling.
Vertical Scale
Enter the vertical scale here. For example 50% reduces the scale one half. Press Tab to apply.
Horizontal Scale
Enter the horizontal scale here.
For example 200% enlarges the scale two times. Press Tab to apply.
Vertical Shear
Enter the vertical shear angle here. The angle can range from -85° to +85°.
Horizontal Shear
Enter the horizontal shear angle here. The angle can range from -85° to +85°.
